Find Parts & Accesories for your Porsche

The requested page could not be found or no longer exists.
From time to time products will become no longer available and we will turn off the listing so as not to show you something that is not available for purchase. 
Please feel free to contact us if you have any questions..

               
Are you looking for:
Right Heater Control Valve Clamp/Control Cable Mount Right Heater Control Valve Clamp/Control Cable Mount
One required per vehicle, clamps the heater pipe from the heat exchanger to the heater control valve as well as supporting the control cable for the heater flap.

Will fit Porsche 911, 912, and 930 models from 1965-89.
Right side only.
Programmable Distributor, 0.231.169.001 for 911 ‘L’

New Programmable 123 Ignition Distributor
Delivered pre-programmed for a 1968 Porsche 911L.
WARNING:  Not programmed for modified engines.
Professional installation is recommended.

Run a new distributor on your classic Porsche!  This distributor has the design character of the original, but with modern electronics. The 123 distributors have been around for over a decade, but they were challenging to set up properly for the 911. Until now!

Comes pre-loaded with our exclusive programming for your stock engine. Our programs for each year and sub-model were developed and tested by a Porsche-trained mechanic, engine builder, and ignition specialist with 34 years of experience. 

This distributor is pre-programmed to replace the Bosch model 0.231.169.001, which featured vacuum retard and was factory equipment on the 911L in 1968. Please note that any changes to the stock programming are made at your own risk.

For modified 911 engines, a qualified, insured mechanic should be employed to adjust the programming to the engine. Incorrect setup or installation can result in severe damage to the engine and distributor.

When properly re-programmed, this distributor can also be set up for other 2.0L / 2.2L engines on the 911 up to 1971. An Apple or Android App allows for wireless adjustment of the ignition curve and provides an electronic dashboard. Range is 500-8K engine RPM.  Other key features include rev-counter, anti-theft PIN code, real time tuning, vacuum advance, and soft rev limiter.

As with all electrical products, this item is non-returnable except for manufacturer pre-approved warranty returns. Arrangements for repairs or warranty service must be made directly with the manufacturer.


Restoration of Your Ignition Distributor, 911SC Euro Restoration Service for YOUR Bosch Distributor
Send your Bosch 0.237.301.007 distributor to us for restoration
No time? See "Related Products" on this page for new distributor option.

When you send us your Bosch 0.237.3001.007 ignition distributor, it will be completely disassembled, media blasted, and polished. All new bushings and shims are installed, along with new springs. The restoration also includes new cap, rotor, seals, gear pin, and hardware.

We make all necessary adjustments to ensure your distributor is operating within factory specs and tolerances. Your rebuilt distributor is then tested on a Sun distributor machine, and printed results are provided to you.

If you would like new cap hold-down clips for your restored distributor, please see part number 930.602.965.00. We also have new drive gears and impulse windings if yours need to be replaced.

Please Note: this service does not include the vacuum can. If your vacuum can is not re-usable then we will have to contact you for options. Not all distributor cores are rebuildable. Damaged cores may require machining and/or parts not included with this service; if that is the case we will contact you.

This is a thorough restoration and we will need your distributor for approximately 4-5 weeks to complete the work. Turnaround times will vary with shop workload and condition of all components.  

Please send your well packed distributor, with your online order number on the the outside of the box, to:

Partsklassik
827 State Route 82
Suite 10251
Hopewell Junction, NY 12533

 


Rear Brake Caliper Mounting Kit, "M" Calipers Vented Rear Brake Caliper Mounting Kit, "M" Calipers Vented
For Porsche vehicles using the "M" Style brake calipers.
Can be used on front and rear mounted brake calipers.
1969-83 models 911, 912, 912E, and 930 using Vented Brake Rotors.
Restoration of Your Ignition Distributor, 911SC Euro Restoration Service for YOUR Distributor, 911SC EURO 1978-79
Send your distributor to us for restoration.
No time? See "Related Products" on this page for new distributor option.

When you send your Bosch 0 237 303 003 ignition distributor to us, it will be completely disassembled, media blasted, and polished. All new bushings and shim kit are installed along with a new spring package. This restoration also includes new cap, rotor, hardware, and seals.

We ensure that your distributor meets acceptable tolerances for vertical and lateral play, and that it performs within original factory specifications. Your rebuilt distributor is tested on our Sun machine, and final test results / curves are included in the box.

If your cap hold-down clips have seen better days, we have replacements available.  Please see part number 930.602.965.00, which fits the 911SC Bosch distributors. We also carry drive gears and impulse generator windings if you would like those items replaced.

Note: not all cores are rebuildable, and some cores require parts or machine work outside the scope of this service. Examples include (but are not limited to) broken magnets, damaged shafts or cases, and so on.  We will contact you to discuss your options if there is a problem with your core.

Please send your well packed distributor, with your online order number on the the outside of the box to:

Partsklassik
827 State Route 82
Suite 10251
Hopewell Junction, NY 12533