Find Parts & Accesories for your Porsche

The requested page could not be found or no longer exists.
From time to time products will become no longer available and we will turn off the listing so as not to show you something that is not available for purchase. 
Please feel free to contact us if you have any questions..

               
Are you looking for:
CV Axle Boot Clamp, Large Side CV Axle Boot Clamp, Large Side
Oetiker Style clamp, requires Oetiker pincer tool to pinch shut.
Inner diameter is 75.5 mm prior to being pinched shut.
For the inner and outer C/V joints; clamps the boot to the joint.
Two required per shaft, sold per each.
For 1969-89 Porsche 911, 930 and 912 models.

Carburetor Gasket Kit, IDA/IDS Weber IDA IDS Gasket Kit
Contains the gaskets for one Weber 3-series carburetor.  
Suitable for a quick carb clean out, not a major overhaul. 
Sold per each, one kit per carburetor.

If doing a full overhaul, see our Master Gasket Kit for Webers. The Master Kit includes 40-50 more parts including additional seals, hardware, teflon bushings, and needles & seats.


We also recommend replacing the following during a full overhaul:

Throttle Plates (edge wear of plates is common)
        sku# 901.100.965.00 for 40mm
        Check that you don't need larger plates due to wear of bore.
   
   Plugs for Needle & Seats (common source of leaks)
         sku# 901.100.801.00
   
   Fuel Inlet Strainers
         sku# 901.100.808.00
   
   Float Bowl Plugs (they easily snap when old, over-tightened)
         sku# 901.100.806.00

   Accelerator pump lever (“ear” attached to throttle rod)
         sku# 45027.007

   Accelerator pump rod assembly (left and right)
         sku# 61287.003, and 61287.002

   Accelerator pump pivot pin
         sku# 32486.000

   Mixture Screws and Screw Springs
         sku# 64750.003 and 47600.007


Finally, be sure to check for the following and replace if needed:

   Brass floats that are collapsed in, corroded, leaky
   Throttle shafts that are worn to 7.95mm or less, or heavily scored
   Auxiliary boosters and chokes with damaged or modified surfaces
   Jets that are deformed or twisted from over-tightening and age
   Corroded or twisted main jet holders

Transmission Gear Anchor Block Anchor Block
For Porsche 911/912 gears 1-5 from 1965-71.
Gears 3-5 for 1972-86.
Gears 1-5 for 914 models.
Gears 3-4 for 930 models up to 1988.
Sold per each.

Carburetor Gasket Set 50 PMO Carburetor Gasket Set 50 PMO 
If we show out of stock, contact us for next availability.

One gasket set will do two carburetors. This set includes gaskets, needles and seats, seals, shims, pump diaphragms, and pump cams.

We also carry PMO jets, air correctors, emulsion tubes, fittings, floats, and more.

Solex P40II Carburetor Article Solex P40-II Carburetor Article
Describes the differences between the different types of Solex P40-II carburetors as used on the 356 and 912 models. Shows the most common wear areas and talks about the shortcomings of the carburetor design.  

Once you have completed the checkout you will be able to access and download your document from our secure server. You will have 7 days to download and save the document on your computer. You can also access your downloadable documents by logging into your account and clicking the "My Account" button located at the the top right hand side of the screen and scrolling down to your order history, then click on the download that you wish to access.